Glen Carbon Mold Removal

24 HOUR SERVICE - CALL US AT 1-800-222-6815

Do you have Mold? Is it toxic mold? Do you have water damage from a flooded basement which is causing moisture to buildup in your home or business? The moisture associated with water intrusions will promote the growth of toxic mold such as Stachybotrys, Penicillium, Aspergillus, and Cladosporium.

The longer an indoor contaminant is allowed to remain intact, the greater its potential impact on human health and on the structural integrity of the facility. Mold can grow on most common building materials if they remain wet for 24 to 48 hours. Special care must be taken during the mold removal and restoration process or serious health hazards can develop.

Our mold remediation technicians are fully trained and are proficient with the latest equipment, materials and techniques. We specialize in remediation of mold, bacteria, water and sewage damage cleanup in your facility.

You can reach us at 1-800 222-6815 if you are having any water, sewage, smoke damage, or mold problems!

Mold Contamination Levels and Appropriate Mold Remediation Response

With mold remediation, the level of contamination determines the level of worker safety. There are four levels of contamination and, hence, four levels of worker safety procedure. Each level requires appropriate clean-up method and treatment of contamination. Every recommended action has been studied as the best way to contain mold contamination and to eliminate mold and mold spores.

Level I

Level I action prescribes mold remediation for a very small affected area, approximately 10 sq ft and even less. With the first level, wearing of respirator, gloves, and goggles is regarded as vital. For level I contamination, evacuating areas near the affected area is not needed. However, infants and individuals with poor respiratory conditions and those convalescing from recent hospitalizations would serve well to stay away from mold remediation areas. There's no need also to contain the area. However, dust suppression should be practiced to ensure that dead and living molds don't spread around.

Contaminated materials that are hard or impossible to clean should be should be bagged and discarded. Workers' entrance and exit areas should be cleaned with bleach solution and water.

Workers should leave area only when it is completely dry.

Level II

Level II action prescribes mold remediation for mid-sized affected area, approximately up to 30 sq ft but no less than 10 sq ft. Remediation workers should also wear protective suits like those of Level I workers. Contaminated surfaces are to be covered with plastic sheets before starting mold remediation process. This is in order to avoid further spread of contamination.

Areas used by worker for entry and exit should be thoroughly cleaned with detergent/bleach solution, then HEPA (High Efficiency Particulate Air) vacuumed.

Workers should leave area only when completely dry already.

Level III

Level III places are those with area size of around 30 - 100 sq ft that require mold remediation. This level requires microbial investigation from industrial hygienists or other health and safety experts. This is to done before remediation process is started. It is strongly advised that remediation personnel must wear N-95 disposable respirator. They should also wear protective gloves and goggles.

Contaminated and adjacent areas have to be covered with plastic sheets before start of mold remediation process in order to prevent further spread of dust and debris. Grills and ventilation outlets should also be covered with plastic sheets. Remediation areas should be vacated, but abandoning adjacent areas is not necessary. However, infants less than a year old and individuals convalescing from surgery and those with weak immune system should leave adjacent areas.

Misting and other dust suppression method should be applied to surface before start of remediation process. Disposable contaminated materials should be put inside impermeable plastic bags, which are to be sealed, then discarded. Again, workers' entry and exit areas should be cleaned with soap, HEPA vacuumed, then let dry.

Level IV

Level IV is contaminated area exceeding 100 sq ft. In this case, mold remediation workers should wear disposable protective suits covering entire body as well as respirators with HEPA cartridges. All contaminated area, ventilation ducts, and grills should be covered with plastic sheets. Again, disposable contaminated areas should be disposed of in sealed plastic bags. Decontamination room and exhaust fan with HEPA filter are to be used in the remediation process. Both decontamination area and contaminated area are to be cleaned with detergent mixture then HEPA vacuumed.

The purpose of mold remediation is to check and resolve moisture problems of a contaminated area as well as to eliminate mold growths. After remediation, the area has to be resurveyed in order to assess the success of remediation process. Process is successful if there are no more mold growths as well as mold smell.

RSS FEEDS

Understanding The Negative Impact Of Mold And How To Effectively Deal With It

1251493299|%e %b %Y, %H:%M %Z|agohover

It should be important for homeowners to note that after an incident of water damage, whether it is due to flooding or a broken pipe, the chances of mold infestation would be high particularly if no preventive measures were put in place after the incident

Understanding Molds And How To Address Mold Problems In The Home

1251493193|%e %b %Y, %H:%M %Z|agohover

Mold is a form of fungus and this tiny organism is present all throughout the year and can be found practically anywhere, whether indoors or outdoors. It can grow on food or other organic material like plants, soil or decaying matter.

How To Deal With A Recurring Mold Problem

1249071728|%e %b %Y, %H:%M %Z|agohover

One of the situations that property owners have to deal with is the presence of molds in the property. Unfortunately, one of its characteristics is that the mold has to recur in the home. It is not unusual to discover a new patch of growth even after you

National Weather Alerts

Short Term Forecast issued November 29 at 11:55AM AKST expiring November 29 at 4:00PM AKST by NWS Fairbanks http://pafg.arh.noaa.gov

1259528100|%e %b %Y, %H:%M %Z|agohover

FOG AND LIGHT SNOW WITH REDUCED VISIBILITY IN FOG AROUND FAIRBANKS AND ACROSS THE MIDDLE TANANA VALLEY. LESS THAN ONE INCH ACCUMULATION OF SNOW EXPECTED THROUGH 4PM.

High Wind Watch issued November 29 at 11:34AM AKST expiring December 01 at 6:00AM AKST by NWS Fairbanks http://pafg.arh.noaa.gov

1259526840|%e %b %Y, %H:%M %Z|agohover

...HIGH WIND WATCH IN EFFECT FROM MONDAY MORNING THROUGH LATE MONDAY NIGHT FOR MOUNTAIN PASSES... THE NATIONAL WEATHER SERVICE IN FAIRBANKS HAS ISSUED A HIGH WIND WATCH...WHICH IS IN EFFECT FROM MONDAY MORNING THROUGH LATE MONDAY NIGHT. STRONG LOW PRESSURE DEVELOPING OVER THE EASTERN ALEUTIANS WILL

Roselle water damage restoration East Peoria mold removal Jerseyville flood damage cleanup Carlinville flooded basement cleanup Marion water removal Galesburg flooded basement cleanup East Moline water removal Carterville document drying Kewanee water damage restoration Murphysboro flooded basement cleanup Lincoln water damage restoration Geneseo flooded basement cleanup Lyons mold removal Franklin Park flooded basement cleanup Canton flooded basement cleanup Lombard mold removal Freeport document drying Bridgeview mold removal Troy water damage restoration Monticello flood damage cleanup Rock Island water removal Greenville document drying Sumner document drying Pittsfield flooded basement cleanup Murphysboro water removal Edwardsville document drying Jacksonville document drying Carterville flood damage cleanup Sewer Backup Cleaning in Detroit Carmi flood damage cleanup Skokie mold removal McLeansboro flooded basement cleanup Mount Prospect water damage restoration Machesney Park mold removal Anna flood damage cleanup